Calypso NMEA Connect Plus: A versatile gateway and range extender to NMEA 0183, NMEA 2000, Bluetooth and WiFi

We are thrilled to present our new gateway. The NMEA CONNECT PLUS connects any Calypso ultrasonic wind meter to a NMEA183 or NMEA000 network, and/or extends your Bluetooth and WIFI signal range. The NCP product range has been designed for maximum versatility, with a number of different models offered:

BLE to NMEA 0183: It converts your ULTRASONIC Portable wind data into NMEA 0183 sentences. It also acts as a BLE repeater allowing you to connect up to 2 Bluetooth devices to monitor your wind data at the same time.

BLE to NMEA 2000: You can use your ULTRASONIC Portable in an NMEA 2000 network by converting the BLE data received from your portable to NMEA 2000 PGNs (messages). It also acts as a BLE repeater allowing you to connect up to 2 Bluetooth devices to monitor your wind data at the same time.



Wired to NMEA2000 + BLE: You can use your ULTRASONIC Wired or Ultra Low Power (ULP485) in an NMEA 2000 network by converting the NMEA0183 wind sentences into NMEA 2000 PGNs. Additionally it sends the data through Bluetooth and allows you to connect up to 2 Bluetooth devices at the same time.

High End: The most versatile model. You can receive wind data from any Ultrasonic wind meter within Calypso’s product range (by the NMEA 0183 interface or by Bluetooth signal), and convert the wind data into NMEA 0183 sentences (wired and Wi‐Fi), NMEA 2000 PGNs and Bluetooth. It can also be used as range‐extender when set up as a Wi‐Fi Repeater. This model selects the wind data source as “first come first served” and it translate it to all output interfaces (NMEA 0183, NMEA 2000, BLE, or WIFI).

POWER

  • NMEA 2000 backbone power: when connected, the NCP is powered from it. This option is compatible with 12VDC supplies typically using 126mA (3 LEN) at 12 VDC. This power source is isolated from the rest of the circuit.
  • USB power: Available when other sources are not available. When another source is available the USB power drain is minimal. USB also used to upgrade firmware.
  • Dedicated VCC input: A dedicated 12VDC input can be used to power the NCP.

NMEA 2000 interface

  • The NMEA Connect Plus is equipped with an NMEA 2000 interface to connect to an NMEA 2000 backbone.
  • NMEA Connect Plus will translate NMEA 0183 wind sentences into NMEA 2000 PGN’s (messages). This feature enables a seamless integration between NMEA 0183 and NMEA 2000 Navigation devices.

NMEA CONNECT PLUS is the result of hundreds of engineering hours striving to design and manufacture what the customer is looking for. For further information: CalypsoInstruments.com



Panbo publishes select press releases as a service to readers and the marine electronics industry. The release contents do not reflect the opinion of the editors and are not fact checked by the editors

4 Responses

  1. Ben Ellison Ben Ellison says:

    I’m really glad to see this new gateway/extender as it seems to add a whole of utility to what was already a very interesting wind sensor in my experience:

    https://panbo.com/calypso-ultrasonic-portable-wireless-wind-and-more/

    In fact, I hope to test the NCP with the Calypso Portable on Gizmo soon. Note that all four models are available now, except that the WiFi extension feature will be added with a firmware update (that will also allow any model to be upgraded to the High End). Also note that cables are extra but if you look it the manual it seems fairly easy to use ones you may already have.

    https://calypsoinstruments.com/shop/product/the-nmea-connect-plus-range-139

  2. Matt Parker says:

    Do you have a good contact for Calypso? I’ve just bought a complete calypso wind system and my NCP plus was dead out of the box. I can’t get a response from the US distributor nor can I get a response from Calypso (been trying for over a week).

  3. Ben Ellison Ben Ellison says:

    Hi Matt, A lot of my contact has been with marketing manager Claudia Esteban, email here:

    https://www.boatshowmanager.com/company_details_4_web.php?sales_id=32055

    Incidentally, I do have an NCP and have found that with latest firmware 1.11 it does reliably connect with the test Calypso Ultra and then outputs apparent wind speed and direction over NMEA 2000.

  4. Matt Parker says:

    Thanks for that, unfortunately that’s one of the emails I’ve been trying with no success.

    As excited as I am to have this setup working on my boat, I cannot currently say anything good about customer support from Calypso or Windmeter systems.

Join the conversation

Your email address will not be published. Required fields are marked *