(Psssst!…back at work but need a little distraction, preferably for a good cause?) The screen shot above is worth seeing full size, but even then doesn’t do justice to the highly dynamic GeoCoastPilot beta program I’ve been entranced with for the last hour or so. The concept is an interactive 3D map that integrates official NOAA Coast Pilot textual information with vector and raster charts, bathy data, and panoramic photographs of key features. In this particular scene I clicked on the Portsmouth Harbor Channel Lighted Range link and the program lined up and highlighted a picture that might make it much easier to actually see the marks. When I then use the screen gizmo above the photo to tilt or turn the scene the photo changes if there are multiple shots available. There’s much more to it, as suggested by the choices at lower right, and for beta software, it seems to work pretty well. If you have a PC running XP or 2000, you go the GeoCoastPilot site and try it yourself, and you should!
This week Maptech sold it paper chart and guide book division to Richardsons’ Publications, which was already producing similar products. In fact, a principal there was working at BBA/ChartKit when Maptech purchased it in 1997. “Things have come full circle.” A nice aspect to this deal is that most of the Maptech print staff will now work for Richardsons’. Sounds like the various Maptech chart books and guides will carry on nicely..
The U.S. Government has stopped distributing electronic updates to the official raster charts for up to 12 months? That doesn’t sound good. NOAA’s download site doesn’t mention a time frame for the “Interruption” but the U.S.C.G. internal bulletin shown in part above is more dire. (It’s published in full on Kurt Schwehr’s site, where you can also check out the Chart of the Future.) This is bad news for all of us who like using RNCs (Raster Navigation Charts) in the many charting programs that support them, not to mention Furuno, which decided to go with U.S. RNCs (and ENCs) in NavNet 3D and is already taking some heat for it. When NOAA decided to serve up RNCs free back in 2005, one of the big pluses was that they would be kept very current, and there were even little patch updates available. Besides, isn’t it depressing to any American that our government can’t even keep a relatively simple and inexpensive program like this going?
It’s wicked hot and sticky here, especially at this big computer, so what a fine time to receive a Panbot e-mail suitable as a guest entry! Richard Stephens—developer behind, and sometimes soggy user of, Memory-Map charting software—recently sailed aboard the Tripp 33TRPXPRS in the Bermuda Ocean Race and reports:
If you'll take a moment to read Ben's comments on Panbo, you'll understand the problem. There is data on the NOAA charts that is not on the NN3D raster chart view. There is a problem with the conversion from the Maptech format to TimeZero format.
Geez Louise! I may not have expressed myself well, but that’s not what I wrote about Furuno NavNet 3D chart issues last week. And the post above is just one of many that I think are way wide of the mark. According to some on Hull Truth the NN3D raster and vector charts for the U.S. are both useless, it was actually Navionics vectors that was shown at the boat show demos, the MFDs show less chart data than the Black Box because of video chip differences, etc. It’s mostly baloney, but Furuno USA has been paying attention to early user dissatisfaction with the vector charts. In fact, I got a call today from Camas with the news that Furuno will be selling U.S. NN3D vector charts based on Navionics data by early 2009. But let’s break that down:
The good news is that more Furuno NavNet 3D MFDs are getting delivered and installed; the bad news is that some of the first users aren’t happy with the charts, neither the rasters nor the vectors. For instance, the two empty MFD12 holes we saw a while back are finally filled, but now the owner—Hull Truth poster “PSW”—is wishing he could use Navionics cards in his MFD12s, as are fellow posters “srmote” and “snowpup”. And I know that our own frequent poster Russ was not pleased with his first look at the charts on his MFD8. My own NN3D experience off Cape Cod did not leave me nearly as negative, but I did note some weaknesses. It helps that I like raster charts and am used to plotting on them, but I didn’t think they worked very well on the 8” display, as suggested in the screen above. Some other levels of zoom/chart scale looked better, and some worse. 3D perspective can put more info on the screen—and fast panning/zooming make it all more tolerable—but there’s just no getting around the fact that you’re looking at a large paper chart through an 8” window. The rasters looked fine to me on the 15” display that was also on the test boat, and I’d guess they’d work OK at 12” (but the Hull Truth gang don’t seem to think so).
After I’d written my first impressions of the new E-Series 4.29 software and the Platinum+ charts it supports, I learned that I hadn’t done the “real” version of the recommended factory/master reset. You see, though Raymarine’s own FAQ is unclear about it, a reset done by powering up while holding down the leftmost soft key is apparently different, and deeper, than the one I’d done from the System Setup menu. I know for sure that this is true, as after a “real” reset yesterday, some of the problems I’d seen went away. For instance, I can pull up the System Diagnostics SeaTalkNG sub-menus now without causing a reset, though the device list there remains strangely empty (the new manual says it’s “for diagnostic use by authorized dealers” anyway). Much more important is how the test E seems be performing even quicker and looking better than what I’d noticed the first time around.
I’ve been bench testing Raymarine’s E-Series V4 software update (aka 4.29) for a while now, mostly with a variety of new Navionics Platinum+ cards I borrowed. If you’ve read the comments to that V4 post, you’ll know that some upgraders have had to revert to 3.31, and I’m not surprised. There’s lots of changes in 4.29, and even my relatively unstressed test E-120—just a bit of N2K input; nothing attached via standard SeaTalk, SThs, or NMEA 0183 right now—goes a little twitchy sometimes. Like suddenly the 3D rotary controls don’t work unless I do a reset. And it invariably resets when I try to query the new STng (N2K) diagnostic screen, no matter what’s on the backbone. Plus I’ve yet to see P+’s live tide/current icons or the now built-in Fish’N Chip bathy data, despite another 4.29 flash and master reset (apparently Raymarine and Navionics are working on that latter one). However, I’d certainly recommend updating; just be prepared to go back to 3.31 if needed, and be on the lookout for the update to the update surely in the works.
Panbo commenters don’t seem very interested in Spot sharing, but I think it’s a cool deal for long range cruisers like Milt and Judy Baker, not to mention working mariners like Capt. Richard Rodriguez. Note how the Baker’s custom message is displayed next to their anchorage on the French Riviera, above and bigger here . And today I notice that Mad Mariner apparently has arranged with West Marine for an extra special Spot deal ($132), and that West customer product reviews are all five star. Even the SSCA offshore guys are taking a cautious look at it
The old days may be something like the new days, but not entirely! Check out the full screen of this NOAA raster/Google maps mashup; it’s the work of Just Magic, aka GeoGarage, and is not only way slicker than what we saw two years back, but is one of the neater Camden Harbor images I’ve ever seen. Of course it helps that Google has high res photo maps for my area now, and they register so darn perfectly with the raster chart. Try it live yourself, fool with those sliders upper right, search out your own harbor, and perhaps join me with big tip of the propeller beanie to those crazy Frenchmen in their GeoGarage.
